hydraulic pressespresse idraulichehydraulic presses

MOULDING AND BENDING PLATE - OLEODYNAMIC PRESSES

press brake for sheet metal - AEM3

PRESS FOR SHEET 200 tonn.

- 200 TONN POWER distributed on 3 hydraulic cylinders
- LIGHT between the OPERATOR SIDE MOUNTS mm. 1,550
- LATERAL LIGHT between the MONTANTI mm. 450X450
- VERTICAL LIGHT between OPEN WORKTOPS mm. 400
- WORKTOP mm. 1500x700
- CYLINDER PRESS RANGE mm. 300
- SPEED CLOSING PRESS mm./sec. 200
- WORKING SPEED PRESS mm./sec. 5
- SPEED OPENING PRESS mm./sec. 200
- WORKTOP HEIGHTS AND MAXIMUM HEIGHT customized for each press
PRESS FOR SIMULTANEOUS 2 FOLDS - AEM3

PRESS FOR SIMULTANEOUS 2 FOLDS.

- IDEAL FOR BENDING OF CALL ON TUBES WITH DIAMETER 10 "3/4 (858 mm. WIDTH PLATE) A D.48" (3830 mm. WIDTH PLATE) AND THICKNESS UP TO 60 mm. THIS ALLOWS YOU TO FOLD THE PRINCIPLE OF WORKING HALF THE TIME
- PRESS "COLUMNS 4"
- POWER 3000 ton. (N° 2 CYLINDERS 1500 ton. / CAD)
- LIGHT BETWEEN THE COLUMNS 4100X600 mm.
- LIGHT BETWEEN PLANS OPEN 1500 mm.
- STROKE OF HYDRAULIC CYLINDER 450 mm.
- SPEED 'DOWN / UP 200 mm/sec.
- SPEED 'MAX POWER AT WORK 10 mm/sec.
- VALVES EQUIPPED WITH CONTROL OF THE PRESS TO LEARNING SYSTEM AND FULL OF SAVING RECIPES, CYCLES TOTAL, PARTIAL CYCLES.
moulding plate

PRESS FOR DRAWING - CUTTING DEEP.

- FOUR COLUMN PRESS
- POWER 1000 ton.
- SPAN 2200x2200x1500 mm.
- STROKE 1000 mm.
- SPEED 200/10/200 mm/sec.
- ELECTRONIC WORKING SPEED REGULATION
- COMPLETE WITH 200TON UPPER BLANK HOLDER STROKE 250 mm.
- COMPLETE WITH 400 ton. LOWER BLANK HOLDER STROKE 500 mm. WITH FOUR 100 ton. LATERAL SHOCK ABSORBERS STROKE 300 mm.
- SELF-LEARNING EQUIPMENT WITH DATA STORAGE AND OTHER ACCESSORIES
- LEVEL IV PROTECTION BARRIERS ON THE OPERATOR’S SIDE AND FIXED WIRE MESH PROTECTION ON THE REMAINING PRESS’S SIDES WITH BIMANUAL PUSH-BUTTON CONTROL PANEL.
TEST PRESS DIES - AEM3

TEST PRESS DIES.

- “PILLAR” PRESS - POWER 1200 ton.
- SPAN 3800x2000x2500 mm.
- STROKE 1200 mm.
- ELECTRONIC WORKING SPEED REGULATION
- COMPLETE WITH 400 ton. UPPER BLANK HOLDER STROKE 250 mm.
- COMPLETE WITH 400 ton. LOWER BLANK HOLDER STROKE 500 mm.
- WITH FOUR 100 ton. LATERAL SHOCK ABSORBERS STROKE 300 mm.
- COMPLETE WITH EXTERNALLY SLIDING BOLSTER TO CHANGE MOULDS UPPER AND LOWER SURFACE EQUIPPED WITH 240 HOLES FOR 50 mm. DIAMETER ELECTRODES
- “FIAT” AND “GERMAN” SPACING METHODSv- SELF-LEARNING EQUIPMENT WITH DATA STORAGE AND OTHER ACCESSORIES
- LEVEL IV PROTECTION BARRIERS ON THE OPERATOR’S SIDE AND FIXED WIRE MESH PROTECTION ON THE REMAINING PRESS’S SIDES MOULD SPOTTING PRESSES.
RESSES FOR BENCH STRAIGHTENING - AEM3

RESSES FOR BENCH STRAIGHTENING.

- “4 COLUMN” PRESS - POWER 600 ton - SPAN 2500X700X1200 mm.
- STROKE 700 mm.
- SPEED 200/7-15/200 mm/sec.
- ELECTRONIC WORKING SPEED REGULATION
- COMPLETE WITH 300 ton
- BLANK HOLDER STROKE 400 mm. WITH 60 HOLES FOR 40 DIAMETER ELECTRODES
- SELF-LEARNING EQUIPMENT WITH DATA STORAGE AND OTHER ACCESSORIES
- LEVEL IV PROTECTION BARRIERS ON THE OPERATOR’S SIDE AND ON THE BACK SIDE AND WITH FIXED WIRE MESH PROTECTION ON THE REMAINING PRESS’S SIDES WITH BIMANUAL PUSH-BUTTON CONTROL PANEL
- PRESSES WITH HEATED MOULDS.
PRESS FOR DISHWASHERS - AEM3

PRESS FOR DISHWASHERS.

- “4 COLUMN” PRESS
- POWER 120 ton
- SPAN 1200X700X450 mm.
- STROKE 400 mm.
- SPEED 200/10/200 mm/sec.
- EQUIPMENT WITH PROPORTIONAL SOLENOID VALVE WITH THREE MANUFACTURING CYCLES: MANUAL, SEMIAUTOMATIC, AUTOMATIC AND WITH BIMANUAL PUSH-BUTTON CONTROL PANEL
- LEVEL IV PROTECTION BARRIERS ON THE OPERATOR’S SIDE AND FIXED WIRE MESH PROTECTION ON THE REMAINING PRESS’S SIDES.
 PRESS FOR METAL CONTAINERS - AEM3

PRESS FOR METAL CONTAINERS.

- LAMIERE/PLATE/SHEET MOULDING PRESS
- “4 COLUMN” PRESS
- POWER 100 ton
- SPAN 1200x1000x1100 mm.
- STROKE 600 mm.
- SPEED 250/15-2/250 mm/sec.
- ELECTRONIC WORKING SPEED REGULATION
- COMPLETE WITH 60 ton BLANK HOLDER STROKE 250 mm. AND WITH 16 HOLES FOR 40 mm. DIAMETER ELECTRODES
- SELF-LEARNING EQUIPMENT WITH DATA STORAGE AND OTHER ACCESSORIES
- LEVEL IV PROTECTION BARRIERS ON THE OPERATOR’S SIDE AND FIXED WIRE MESH PROTECTION ON THE REMAINING PRESS’S SIDES
- BIMANUAL PUSH-BUTTON CONTROL PANEL.
HYDRAULIC PRESS FOR WORKSHOPS - AEM3

HYDRAULIC PRESS FOR WORKSHOPS.

- “4 COLUMN” PRESS
- POWER 200 ton
- SPAN 1520x1520x800 mm.
- STROKE 500 mm.
- SPEED 28/3/28 mm/sec.
- COMPLETE WITH 70 ton BLANK HOLDER STROKE 150 mm. AND WITH 30 HOLES FOR 40 mm. DIAMETER ELECTRODES
- EQUIPMENT WITH PROPORTIONAL SOLENOID VALVE WITH THREE MANUFACTURING CYCLES: MANUAL, SEMIAUTOMATIC, AUTOMATIC AND WITH BIMANUAL PUSH-BUTTON CONTROL PANEL.
MOULD SPOTTING HYDRAULIC PRESSES - AEM3

MOULD SPOTTING HYDRAULIC PRESSES.

- “4 COLUMN” PRESS
- POWER 60 ton
- SPAN 2000x1000x1300 mm.
- STROKE 700 mm.
- SPEED 200/8/200 mm/sec.
- ELECTRONIC WORKING SPEED REGULATION WITH SELF-LEARNING EQUIPMENT, DATA STORAGE AND OTHER ACCESSORIES
- LEVEL IV PROTECTION BARRIERS ON THE OPERATOR’S SIDE AND FIXED WIRE MESH PROTECTION ON THE REMAINING PRESS’S SIDES WITH BIMANUAL PUSH-BUTTON CONTROL PANEL.
PRESSES FOR BENDING PLATE - AEM3

PRESSES FOR BENDING PLATE.

- “4 COLUMN” PRESS
- POWER 100 ton
- SPAN 2500x1350x2000 mm.
- STROKE 1250 mm.
- SPEED 400/15/400 mm/sec.
- ELECTRONIC WORKING SPEED REGULATION
- SELF-LEARNING EQUIPMENT WITH DATA STORAGE AND OTHER ACCESSORIES WITH BIMANUAL PUSH-BUTTON CONTROL PANEL
- LEVEL IV PROTECTION BARRIERS ON THE OPERATOR’S SIDE AND ON THE OPERATOR’S BACK SIDE AND WITH FIXED WIRE MESH PROTECTION ON THE REMAINING PRESS’S SIDES.