hydraulic pressespresse idraulichehydraulic presses

CALIBRATING PRESSES - OLEODYNAMIC PRESSES

AUTOMATED SYSTEM FOR CALIBRATE PIPES - AEM3

AUTOMATIC PIPE CALIBRATION MACHINE.

- PRESS CALIBRATING MACHINE 4000TON TO CALIBRATE WELDED TUBES (MADE FROM METAL) FROM DIA. A 168MM DIA. 1250MM THICKNESS FROM 10MM TO 70MM STAINLESS STEEL
– DUPLEX
- SUPERDUPLEX
- POWER EXTRACTION 250TON
- LOAD HANDLING ON A ROLLER TUBE ANTERIOR AND POSTERIOR
- TRANSLATION AND ROTATION PIPE FULLY AUTOMATED WITHOUT A CRANE
- WITH POWER PULLER 50TON POSITION ON THE PLAN MOBILE
- MOVING OUT OF AUTOMATED MOULD DIE LOCK HYDRAULIC OPERATION UNLOADING / LOAD PRACTICABLE DIES IN 5 MINUTES WITH MAXIMUM DIE ALREADY PLACED
- TOTAL POWER ENGINE INSTALLED ABOUT 300KW
- ALL INSTALLED ENGINES ARE EQUIPPED WITH INVERTER THAT ALLOW AN ENERGY SAVING UP TO 50%.
SYSTEM CALIBRATION PIPES - AEM3

SYSTEM CALIBRATION PIPES.

- PIPE-SIZING EQUIPMENT
- “PILLAR” PRESS WITH “LINEAR” BEARINGS
- TWO-SPEED POWER DRIVEN AUTOMATIC EXCHANGE OLEO-DYNAMIC PRESS
- POWER 2500 TONS SPAN 2000X2000 mm.
- SPAN BETWEEN OPEN SURFACES 2000 mm.
- CYLINDER STROKE 1100 mm.
- SPEED 200/50/10/5 mm/sec
- COMPLETE WITH 20 ton. OLEO-DYNAMIC EXTRACTING PISTONS, STROKE 650 mm. and 40 ton. EXTRACTOR WITH SADDLES ON THE BOTTOM PART
- STROKE 550 mm.
PIPE FORMING SYSTEMS - AEM3

PIPE FORMING SYSTEMS.

- “PILLAR” PRESS WITH “LINEAR” BEARINGS
- USED FOR MANUFACTURING WELDED DUPLEX AND SUPER DUPLEX STAINLESS STEEL PIPES
- MAXIMUM 60 mm. THICK
- POWER 3500 ton.
- FRONT SPAN (OPERATOR’S SIDE) 2250 mm.
- DEPTH SPAN (LATERAL SIDE) 1500 mm.
- SPAN BETWEEN OPEN CYLINDER AND WORK TABLE 2000 mm.
- SPEED 200/10/200 mm/sec.
- PRESS WITH SLIDING GUIDES
- COMPLETE WITH TWO 200 ton CYLINDERS STROKE 600 mm. FOR STRAIGHTENING THE PIPE-IN-PROCESS
- COMPLETE WITH FOUR 20 ton. CYLINDERS STROKE 650 mm. FOR ROTATION AND SLIDING OF THE PIPE-IN-PROCESS
- COMPLETE WITH TWO 20 ton. CYLINDERS STROKE 650 mm. FOR EXTRACTION OF THE PIPE-IN-PROCESS PLACED ON THE MOBILE PLANE
- COMPLETE ALSO WITH MOULD LOADING /UNLOADING
- SELF-LEARNING EQUIPMENT WITH DATA STORAGE AND OTHER ACCESSORIES WITH BIMANUAL PUSH-BUTTON CONTROL PANEL
- LEVEL IV PROTECTION BARRIERS ON THE OPERATOR’S SIDE AND AT THE BACK SIDE AND WITH FIXED WIRE MESH PROTECTION ON THE REMAINING PRESS’S SIDES.
PRESSES FOR HYDRAULIC PIPES - AEM3

PRESSES FOR HYDRAULIC PIPES.

- PRESSES USED TO EXPAND HYDRAULIC PIPES “PILLAR” PRESS WITH “LINEAR” BEARINGS
- USED FOR MANUFACTURING DUPLEX AND SUPER DUPLEX WELDED
- STAINLESS STEEL PIPES UP TO 60 mm. THICK 2500 ton. POWER
- FRONT SPAN (OPERATOR’S SIDE) 2250 mm.
- DEPTH SPAN (LATERAL SIDE) 1500 mm.
- OPEN CYLINDER SPAN
- WORK TABLE 2000 mm.
- SPEED 200/10/200 mm/sec.
- ELECTRONIC WORKING SPEED REGULATION COMPLETE WITH 2 70TON CYLINDERS 650MM STROKE FOR PIPE-IN-PROCESS ROTATION
- COMPLETE WITH 2 20 ton. CYLINDERS 650 mm. STROKE FOR PIPE-IN-PROCESS EXTRACTION PLACED ON THE MOVING PLANE
- SELF-LEARNING EQUIPMENT WITH DATA STORAGE AND OTHER ACCESSORIES AND BIMANUAL PUSH-BUTTON CONTROL PANELS
- LEVEL IV PROTECTION BARRIERS ON THE OPERATOR’S SIDE AND ON THE BACK SIDE AND WITH FIXED WIRE MESH PROTECTION ON THE REMAINING PRESS’S SIDES.
DUPLEX AND SUPER DUPLEX STAINLESS PIPES - AEM3

DUPLEX AND SUPER DUPLEX STAINLESS PIPES.

- “PILLAR” PRESS WITH “LINEAR” BEARINGS CYLINDER POWER 2000 Ton
- CYLINDER STROKE 1010 mm.
- OPEN CYLINDER SPAN - WORK TABLE 2000 mm.
- OPERATOR’S SIDE SPAN 1820 mm.
- LATERAL OPERATOR’S SIDE SPAN 1050 mm.
- COMPLETE WITH FOUR 20 Ton FEEDING CYLINDERS AND TWO 200 Ton FEEDING CYLINDERS
- USED FOR MANUFACTURING WELDED PIPES
- COMPLETE WITH AUTOMATIC MOULD CHANGING SYSTEM ON BOTH SIDES.
HYDRAULIC PIPE-SIZING PRESSES - AEM3

HYDRAULIC PIPE-SIZING PRESSES.

- PRESSES USED TO BEND PIPES “PILLAR” PRESS WITH “LINEAR” BEARINGS
- CYLINDER POWER 1500 Tons
- CYLINDER STROKE 800 mm.
- OPEN CYLINDER
- WORK TABLE 1500 mm.
- OPERATOR’S SIDE SPAN 1470 mm.
- LATERAL OPERATOR’S SIDE SPAN 1050 mm.
- COMPLETE WITH EIGHT 20 Ton FEEDING CYLINDERS AND TWO 200 Ton FEEDING CYLINDERS
- USED FOR MANUFACTURING WELDED PIPES
- COMPLETE WITH AUTOMATIC MOULD CHANGING SYSTEM ON BOTH SIDES.
PRESSES USED TO BEND STEEL PIPES - AEM3

PRESSES USED TO BEND STEEL PIPES.

- “PILLAR” PRESS WITH “LINEAR” BEARINGS
- USED FOR MANUFACTURING WELDED PIPES IN DUPLEX AND SUPER DUPLEX STAINLESS STEEL UP TO 40 mm. THICK SPAN OF THE OPEN CYLINDER
- WORK TABLE 1500 mm.
- FRONT SPAN (OPERATOR’S SIDE) 1800 mm. NON HORIZONTAL LATERAL SPAN 1400 mm.
- DEPTH SPAN (LATERAL SIDE) 1500 mm.
- SPEED 200/10/200 mm/sec.
- ELECTRONIC WORKING SPEED REGULATION
- COMPLETE WITH FOUR 20TON CYLINDERS STROKE 650MM FOR PIPE-IN-PROCESS EXTRACTION AND ROTATION (TWO PLACED ON THE MOVING PLANE AND TWO PLACED ON THE LOWER FIXED PLANE)
- SELF-LEARNING EQUIPMENT WITH DATA STORAGE AND OTHER ACCESSORIES AND BIMANUAL PUSH-BUTTON CONTROL PANELS
- LEVEL IV PROTECTION BARRIERS ON THE OPERATOR’S SIDE AND ON THE BACK SIDE WITH FIXED WIRE MESH PROTECTION ON THE REMAINING PRESS’S SIDES PIPE-SIZING PRESSES.
PRESSES FOR MANUFACTURING STAINLESS SQUARE PIPES - AEM3

PRESSES FOR MANUFACTURING STAINLESS SQUARE PIPES.

- PRESSES FOR MANUFACTURING STAINLESS RECTANGULAR PIPES
- CYLINDER POWER 1500 Tons
- CYLINDER STROKE 650 mm.
- OPEN CYLINDER SPAN
- WORK TABLE 1650 mm.
- OPERATOR’S SIDE SPAN 1055 mm.
- LATERAL OPERATOR’S SIDE SPAN 855 mm.
- COMPLETE WITH TWO 20 Ton FEEDING CYLINDERS
- USED FOR MANUFACTURING WELDED PIPES.
MOULDS FOR PRESSES - AEM3

MOULDS FOR PRESSES.